Relay Circuits
- Page 11-
The CoolRunner-ii board has external 5v Relay interfacing, indicated as in Figure. ULN2803 is used as a driver for CPLD I/O lines, drivers output connected to relay modules. PTB connector provided for external power supply if needed... -
The Universal Development Board has external 5v Relay interfacing, indicated as in Figure. ULN2803 is used as a driver for FPGA I/O lines, drivers output connected to relay modules. PTB connector provided for external power supply if needed. Signal LEDs for.... -
The Spartan-3 board has external 5v Relay interfacing, indicated as in Figure. ULN2803 is used as a driver for FPGA I/O lines, drivers output connected to relay modules. PTB connector provided for external power supply if needed... -
The Spartan-3an board has external 5v Relay interfacing, indicated as in Figure. ULN2803 is used as a driver for FPGA I/O lines, drivers output connected to relay modules. PTB connector provided for external power supply if needed... -
The Spartan-6 board has on board 5v Relay interfacing, indicated as in Figure. ULN2803 is used as a driver for FPGA I/O lines, drivers output connected to relay modules. PTB connector provided for external power supply if needed... -
Using an Atmega8-8PU (configured for 8MHz with external crystal), a Nokia 5110 lcd, and a transistor to handle the pulses from a reed relay. A 3. 3V regulator provides the voltage for the entire circuit. Everything has been mounted on a test board, including.... -
Following a power interruption, all relays assume their previous state before the power interruption. (relay states and PIN are stored in non-volatile memory) An Motorola MC145436 DTMF decoder is used, this IC is clocked with a common 3. 58Mhz NTSC colour.... -
-
In this circuit, using a photoelectric coupler can reach 100G? isolation between TTL and relay circuit, it avoids relay noise and peak voltage influencing TTL circuit. When the TTL input singal is high, Q1 turns on, there is no current in LED, and there is.... -
the circuit has two-stage circuit structures, the timing time is about 0. 5~12s, and in figure (b), the range of the timing time is 1~160s. The parameters of transformer: iron chip: M42/15. 7 silicon steel sheet; winding: 0. 18mm, enameled copper wire.... -
As shown in Figure, the circuit usestwo time relays KT1, KT2 to connect with thecontactsofelectric contact pressure gauge SP in series. When liquid or gas pressure has not yet reached, it can overcome thetrembling or spark phenomenons because of the SP`s.... -
This simple circuit shown int the schematic diagram actives the switch using sound. We can use this circuit for various applications, such as automatic (sound-controlled) disco light or car s LED light show. The Q1 amplify the audio from mic. The R1 is used.... -
This is a Driving Relay circuit using 555 IC. The circuit is used to drive a relay to avoid 555 hangs up, it uses an inductive feedback. The coil is prevented.... -
LM111 comparator can be used o design a relay driver with TTL strobe, this can be used to provide more control of your relay driver. You can control the strobe.... -
Configured with capacitive coupling (by inserting a small cap between photo-transistor and bipolar transistor), this relay circuit will respond only to rapid.... -
This relay circuit is controlled by almost any type of infrared remote controller. This circuit works on assumption that almost all remote controller use high.... -
There are only four components required, and the cost for these is around 70p, so it would be a good candidate for a classroom exercise. Even a cheap relay like the Omron G5LA-1 5DC can switch loads of 10A at 240V. A word of caution: don`t tinker with mains.... -
Is equivalent to single-pole electromechanical latching relay with electrically isolated solenoid. Once turned on, circuit remains in conducting state even though line voltage is interrupted for long periods of time. Positive reset action requires that.... -
Solid-state relay circuit with input protection of the MOC3011 triac driver. The input voltage to the protection circuit can be 3 to 30 volts DC (courtesy Motorola Semiconductor Products Inc. ). .. -
The Haynes manuals is extremely confusing regarding the labeling of the relays on Spitfires. The two ways they confuse readers is 1. the illustrations show right hand drive cars with different locations for relays, and 2. the naming of the relays is strange.... -
This is the circuit diagram of a voice operated relay. It similar with sound activation switch circuit which will turn on and turn off (connect and disconnect) the switch depending on the sound input. The output switch of this circuit is ac.... -
The following schematic shows the Relay Wiring Circuit Diagram for controlling an Air Conditioner or other higher high-current device from a microcontroller.... -
You can use a Cmos 4001 or a Cmos 4011 in this circuit. They have four - two-input - gates. In each case - the two inputs are joined together. So the gates are being used as simple inverters. = This means that when the two inputs are high - the output will....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
This hybrid circuit uses a mixture of transistors, an IC and a relay and is used to automatically...
This electronic lock can be used with any type of iButtons you may already have, since the only...
A relaxation oscillator is used to flash an LED in the base circuit. Cl is charged slowly through...
This circuit utilizes the MRF123 TMOS power FET. The MRF134 is a very high gain FET that is...
Channel 1 is wired as a voltage follower and is turned on during the track/sample time. Ifthe...
The ROMs or PROMs must have the correct code for converting the data from the NE5037 -used as...
If you want to do the ground loop elimination in audio path, you have to cut the galvanic...
This versatile amplifier circuit is designed and submitted by Mr Seetharaman Subramanian from...
Using the LTC4060 integrated circuit, can be designed a very simple smart NiMH battery charger...