Remote Control Circuits
- Page 11-
As the only electronics engineer in my family and circle of friends, it is sometimes not possible to evade an appeal for help. This time the request came from a friendly elderly lady in a retirement home. In her room the light switch by the door and the pull.... -
Just an early post to share some work on remote controlling the PXA-70x Multimedia controllers. Target For my new install, I have been looking at no.... -
The design of this project depends on the sensors. The control module and the robot both contain sensors. The computer, in turn, analyzes the signals to make the appropriate output actions. As previously mentioned, the potentiometers are the sensors on the.... -
The entire control is handled by a Microchip PIC18F46K20-I/PT microcontroller, programmed with a firmware that controls the GSM/GPRS module`s activity, reads the logic condition of the two opto-isolated inputs and sends commands to the two relays in the.... -
Power is supplied by continuous voltage, not always stabilized (applied to PWR + and -) at a value between 5 and 32V; such voltage is filtered at the bottom by the diode protecting against polarity inversion (D1) through condensers C1 and C2. Fuse F1 enables.... -
The entire remote control is handled by a PIC that controls the GSM/GPRS module`s activity, reads the room temperature through a Dallas DS1820 smart probe, controls the logical state of two opto-isolated inputs, and gives commands to the two relays. In.... -
This GSM Mobile is used for our Remote Control (for example Gate Control, Temperature Control . ). We use the word module` because, unlike what we did in ourremote control projects, this time around the mobile phone is not mounted on a printed board, but.... -
The full GSM thermostat is managed by a Microchip PIC18F46K20-I/PT microcontroller, programmed with a firmware that controls the temperature and takes care of the communication with the GSM module which is the component named GSM; this is, in fact the small.... -
A wood table with many holes with different diameters that house the optical fibers. The size of the ceiling lamp (90 cmx 60 cm) did not allow me to use a single bundle of fibers and this is the reason of the two beams I used, each of which comes with a LEDs.... -
Using an ATmega 2560 and therefore the heart of Arduino, we have developed a universal remote control with GSM. This allows to control 2IN/2OUT, DTMF key, gate control and GSM thermostat activated remotely. The remote control is easier, thanks to the.... -
Installing a small dash mounted 2 speed fan in my motorhome. What`s the best way Use your 1 channel and then find a relay or use the 4 channel and use the seperate wires [1 low spd. &1 high spd ] Any other lideas Would it hurt the unit if it were placed in.... -
This is a very easy circuit that every one could make and have fun. This project popped out of nowhere, one day that i was trying to control the TV from the serial port of the computer. It took me no more than a few minutes to understand the simple method.... -
.jpg "Remote Doorbell Controller")
I usually can`t hear the doorbell when I`m in the basement. This project describes how to add an inexpensive remote doorbell to your existing household doorbell. My doorbell runs off of a 24VAC transformer that is live all the time. Someone presses the.... -
The simplest solution for implementing joystick control for a robot would be to program the actions in software in a microcontroller. But, since many readers prefer off-the-shelf parts, this circuit is going to be made with diodes, resistors, transistors,.... -
The laser-pointer detection circuitry is able to determine when a laser light is aimed at a particular photosensor. If the laser is aimed at the top sensor, the comparator chip outputs on . If the laser is aimed at the bottom sensor, the comparator chip.... -
IR remote control for my Nikon DSLR camera. Not that I absolutely need one, surely I don`t need it bad enough to get one for about ‚¬30 or ‚¬40 from e-bay. However it would make a nice little in-between project. Big Mike explains the very easy protocol used.... -
A schematic diagram of the remote-control receiver is shown. The heart of the circuit is IC1, a PIC16C54 8-bit CMOS manufactured by Microchip. The microcontroller stores its data in IC2, a 93LC46 1-kbit serial EEPROM (electrically erasable programmable.... -
Starting from today I will try to post interesting Arduino projects from around the web. I am novice in this domain but I am giving my best to fully understant it. I must say from the begining that the projects are not developed by me and I will link the.... -
Is infrared emission circuit diagram. NE555 circuit generates a 40kHz pulse which is sent by the infrared emission control SE303 after beingamplified by VT. (b) is remote receiver and infrared dimming circuit composed of the KA2184. LS7232 is an integrated.... -
As shown in the diagram above, it is a radio remote control dimmer circuit. The radio remote control dimmer circuit adopts micro radio transmit/receive module and light modulation ASIC. So the circuit is concise and easy to produce. It works reliably. And.... -
The circuit is not only used for the latch output, but also for non - latched output, SB is control switch. When SB and VDD are turned on, it is in the latch output state, then the sixteen output ends are out control of Io output state; when SB and Io output.... -
HS101/HS201 are a pair of tiny radio transceiver components. The working frequency is 280MHz. It is suitable for digital signal transmission. The control distance is 30 ~ 100m. All the components including the antenna are packaged in one. It is easy to use..... -
The circuit uses the long-wave wireless transceiver T630/T631, controlled 6-channel load. The features are low-power, high anti-interference ability and simple structure etc.... -
TDC1808/TDC1809 is a pair of wireless remote control transmitter and receiver component. They use an internal antenna, transmitting digital signals or analog signals. It is suitable for a variety of wireless remote control device. The features are small.... -
Figure (a) is the infrared emission circuit that composed of 12 the keyboard and S2559. Figure (b)shows DTMF decoder circuit and channel control circuit composedof the MT8870. Figure (c) is the voltage amplifier circuit composed of two-op ampLM358.... -
The DTMF codec is the abbreviation of the dual-tone multi-frequency codec. The multiple-channel infrared remote control switch circuit which is composed of the DTMF is as shown in the figure. It is composed of the infrared remote control signal emitter, the....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
This machine essentially does three things: It controls the process temperature, provides...
In the circuit exist a simple power amplifier 60W in the 8 ohm and 80W in the 4 ohm, with...
We are going to build a START-STOP drive (as commonly found in professional tools), that is a...
Here we use the PIC16711. Rechargeable battery capacity is rated in mAH (milliampere-hours). The...
Intended as a replacement for generally poorly regulated "wall-type" ac/dc adapters, this...
Our eyes are very sensitive to light but they cannot see the IR (Infrared) radiations so it is...
The AK4532 is a low-cost high-quality 16-Bit CODEC designed specifically for Internet Boxes,...
This kit, designed by Jan G0BBL and implemented and distributed by Tony KB9YIG, is a plug-in...
Ultrasonic drilling machine is the dairy industry essential jewelry processing machinery, mainly...