Remote Control Circuits
- Page 12
-
The DTMF infrared remote control circuit. The DTMF encoded signal can be decoded by the special decoder and the PLL audio decoder LM567. But the DTMF encoded signal which is decoded by only one decoder, has only one frequency, one group of control signal is....
-
-
LS-2 remote control switch infrared sensor module is basically the same with the LS-18, in addition, it isused as a reflector. LS-2 Pin diagram form LS-2 internal block diagram Electrical parameters LS-2 remote control switch module operating voltage is 4 ~....
-
The electric car remote control circuit diagram not only can make the model car move forward and backward, but also turn left and right turn, it is simple, easy to operate. Radio remote control receiver demodulation circuit uses TWH9238 components, the....
-
-
Electric single-girder cranes is also known as electric hoist. It is commonly used in small factories lifting handling equipment. Usually it is always used with drag line switching noytoperation, which is not very convenient. The circuit is composed of radio....
-
The receiving circuit: the infrared signal is inputed to MC3373 from 7 foot by phototube, the amplified signal outputs from 1 foot, it is transported into the 12 foot of decoder 8802. When the transmitter F is pressed, the voltage of 8802`s 11 foot up to 2.....
-
-
The HT6337 is designed as one kind of infrared remote control receiving decoder circuit that can be used in the electric fan application. It uses the 28-pin dual-row DIP package, the matching model is HT12C. The HT6337 is one of the series products. The....
-
TDA5200 is a low-power single-chip ASK superheterodyne receiver circuit. Its operating frequency range has two block. They are 868 ~ 870MHz and 433 ~ 435MHz. The circuit is highly integrated. It has few external components, perfect function. It is a single....
-
The diagram is human infrared remote sensing lamp circuit. It uses trace infrared heat sent out by human to remote control the open or close of lap. This human infrared remote sensing lamp trigger sensitivity is very high ( can work in 10m distance),....
-
Figure 1 is an improved trigger timing circuit composed of 2 PUT. If you add the set signal, the circuit will be set, transistor VT1 turn to the conduction state, the relay K will be energized action. It supplies voltage for the delay voltage at the same....
-
-
-
-
-
The remote control transmitter is composed of the DTMF generator and the FM transmitter circuit. Here we use one piece of UM91214B phone specific IC to produce the DTMF signal, the 3V power supply voltage is supplied by the 3V zener tube D1.The transmitter....
-
-
As shown in the figure is a preset outage timer of electric cooker circuit. Time of the timing circuit ranges from 1 hour to 12 hours, which can be regulated by PR.The timing mode is counting typeand control method mode is preset outage timing. The circuit....
-
-
The remote control electric hoist control circuit consists of the wireless transmitter, wireless receiver control circuit and the main control circuit. Wireless transmitter uses TWH9326 four key BP transmitter. Wireless receiver control circuit consists of....
-
The remote control robot circuit is as shown in the figure. The figure 2-36(a) is the circuit diagram, the figure 2-36(b) is the operating timing diagram. The rotation process of the rebot is: in the circuit, the ultrasonic launching circuit is composed of....
-
The SC41343 is designed as one kind of infrared, ultrasonic or RF remote control launch coding circuit. The internal circuit is composed of the sequence generator, control logic circuit?4-bit shift register?data extraction circuit and the latch circuit.....
-
The SL517 is designed as the audio, RF or infrared decoder circuit that can be used in the electronic toy application. The internal circuit is composed of the analog amplifier, the frequency divider, the bistable circuit and the driver. Features It uses the....
-
When the current is less than the value set, the bias current provided by R1 leads the P3 to be saturated to conduct. And it can not afford to control the current. When the current is greater than or equal to the set value, the pressure drop on R would....
-
In this figure S1 can start timing and when the timer starts, turning this switch has no effect.S2 is the OFF switch in the middle and turning this switch can make the timer complete the procedure: charging-open circuit-discharging. Because of charging....
-
In the figure is the FM modulation circuit of crystal oscillator. FM modulation has direct and indirect FM ways, the direct FM method is to directly change the frequency of the oscillating circuit, it`s simple, but as it is the LC oscillating circuit, the....
-
See as the figure, the controller consists of liquid level, trigger controller and step-down rectifier circuit, etc. The water level detecting poles of a, b and c compose the bias circuit as the water level detector with W1, R1, R2 and R3. When the water....
-
Is an eight-way signal remote control selection circuit composed of ZHJ-9904 ; (B) is remote control transmitter circuit; (C) is the eight-way switch control circuit; (D) is remote control transmitter...
-
This is the electric thermometer circuit composed of LM134. In the circuit, the voltage or current output by LM134 is in proportion to the thermodynamics temperature, which can be read out on the 100?A meter, the test temperature range of the meter is....
-
The switch shut off time delay circuit is shown as below. The switch shut off time delay circuit is composed of the timer, optocouplers, bridge SCR, SCR AC switch. When the control button is released, the keeping motor or other AC start power for 1 hour.....
-
When this thermometer is used in the room, it can work in the intermittent way, and this working state can be kept in the temperature test circuit, because internal temperature doesn`t change sharply. The astable multi-resonance oscillator consists of VT1....
-
It can set delay time according to the voltage Us and resistor R. In the circuit, S1 is the the discharge switch of capacitor C. When the switch S1 is closed, the stored charge on C will be released through S1 to ensure the accuracy of the delay time the....
-
A few time ago I decided to create a media center box to replace my DVD player, sattelite receiver, VCR and my kid`s Play Station 2, toone device. So, I made a core 2 duo processor system that actually replaced with succeed, all my electronic devices. The....
-
The basic small-range remote controls are 2, Infrared and RF (Radio Frequency). One of the weaks of Infrared is that the signal can not pass the walls. So, if you wantto control your garage door, the only way is to use some RF remote control. The circuit....