2V-25V DC Power Supply Schematic
#LM338
#variable power supply
#regulated power supply
#DC power supply
#5A power supply
#adjustable regulator
#2V-25V
#voltage regulator
#power supply schematic
#parts list
Description: Construct a variable 5A, 2V to 25V regulated power supply using the LM338 adjustable regulator. A power supply schematic and parts list are provided here.
The LM338 adjustable voltage regulator is a versatile component capable of providing a regulated output voltage ranging from 1.25V to 37V with a maximum output current of 5A. To construct a variable power supply utilizing the LM338, the following components are typically required: the LM338 regulator itself, resistors for setting the output voltage, capacitors for input and output stabilization, a heat sink for thermal management, and a suitable transformer or power source.
The schematic for the power supply begins with the AC input, which is typically stepped down using a transformer. The output of the transformer is rectified using a bridge rectifier composed of four diodes, converting the AC voltage to a pulsating DC voltage. This pulsating DC voltage is then filtered using large electrolytic capacitors to smooth out the ripples, providing a more stable DC input to the LM338.
The LM338 requires two resistors to set the output voltage. By connecting a variable resistor (potentiometer) in series with a fixed resistor, the output voltage can be adjusted from 2V to 25V. The formula for the output voltage (Vout) is given by Vout = 1.25V * (1 + R2/R1), where R1 is the resistor connected from the output to the adjust pin, and R2 is the resistor connected from the adjust pin to ground.
To ensure stability and performance, it is crucial to include bypass capacitors at both the input and output terminals of the LM338. A 0.1µF ceramic capacitor is typically placed close to the output pin to filter high-frequency noise, while a larger electrolytic capacitor (e.g., 10µF) may be used at the input to improve transient response.
Thermal management is also an important consideration. The LM338 can dissipate significant heat, especially at higher output currents. Therefore, a suitable heat sink must be attached to the regulator to prevent thermal shutdown during operation.
Finally, a voltmeter and ammeter can be added to the output for monitoring the voltage and current supplied to the load, enhancing the usability of the power supply. The entire assembly should be housed in a suitable enclosure to ensure safety and protect the components from damage.Construct a variable 5A, 2V to 25V Regulated Power Supply using LM338 Adjustable Regulator. Power supply schematic and parts list is provided here ..
The LM338 adjustable voltage regulator is a versatile component capable of providing a regulated output voltage ranging from 1.25V to 37V with a maximum output current of 5A. To construct a variable power supply utilizing the LM338, the following components are typically required: the LM338 regulator itself, resistors for setting the output voltage, capacitors for input and output stabilization, a heat sink for thermal management, and a suitable transformer or power source.
The schematic for the power supply begins with the AC input, which is typically stepped down using a transformer. The output of the transformer is rectified using a bridge rectifier composed of four diodes, converting the AC voltage to a pulsating DC voltage. This pulsating DC voltage is then filtered using large electrolytic capacitors to smooth out the ripples, providing a more stable DC input to the LM338.
The LM338 requires two resistors to set the output voltage. By connecting a variable resistor (potentiometer) in series with a fixed resistor, the output voltage can be adjusted from 2V to 25V. The formula for the output voltage (Vout) is given by Vout = 1.25V * (1 + R2/R1), where R1 is the resistor connected from the output to the adjust pin, and R2 is the resistor connected from the adjust pin to ground.
To ensure stability and performance, it is crucial to include bypass capacitors at both the input and output terminals of the LM338. A 0.1µF ceramic capacitor is typically placed close to the output pin to filter high-frequency noise, while a larger electrolytic capacitor (e.g., 10µF) may be used at the input to improve transient response.
Thermal management is also an important consideration. The LM338 can dissipate significant heat, especially at higher output currents. Therefore, a suitable heat sink must be attached to the regulator to prevent thermal shutdown during operation.
Finally, a voltmeter and ammeter can be added to the output for monitoring the voltage and current supplied to the load, enhancing the usability of the power supply. The entire assembly should be housed in a suitable enclosure to ensure safety and protect the components from damage.Construct a variable 5A, 2V to 25V Regulated Power Supply using LM338 Adjustable Regulator. Power supply schematic and parts list is provided here ..
Micropower Linear Voltage Regulator in the Battery Charger Circuit
The ADM666A application note provides a detailed explanation of a low-cost battery charger circuit, including maximum output voltage, charge termination voltage calculation, battery voltage level monitoring, and circuit efficiency optimization. The ADM666A utilizes an NPN transistor and a P-channel FET....
Universal Laboratory Power Supply Circuit
The design's value is derived from the use of IC1, an LM317HVK adjustable series-pass voltage regulator, which provides broad-range performance along with voltage-setting and current-limiting functions. The input to IC1 is sourced from the output of BR1, which is filtered...
Variable Power Supply 1.2-55 Volt Uses Switching Technology for High Efficiency
Designing a wide-range variable power supply using a linear regulator is straightforward; however, it suffers from poor efficiency when regulating a constant 60-volt source.
A wide-range variable power supply can be implemented using a linear regulator, which allows for adjustable output...
12v power supply circuit
This project involves a straightforward and practical 12V power supply circuit utilizing the LM7812 integrated circuit (IC). The LM7812 is a three-terminal fixed voltage regulator IC housed in a TO-220 package. It incorporates several built-in features such as thermal shutdown,...
Variable PSU
A variable power supply with adjustable voltage and current outputs utilizes the L200 regulator. This power supply features independent voltage and current limits. The mains transformer is rated at 12 volts with a 2 amp secondary output, while the primary...
symmetrical regulated power supply and variable 0 to 30v 2a
This circuit can deliver up to 15V per section (-15V and +15V), or up to 30V as a whole, for a maximum consumption of 2A. With modifications, it could be adjusted to provide up to 5A or more. Transistors Q1...
Easy exchange of magnetic saturation voltage regulator circuit
Easy exchange of magnetic saturation voltage regulator circuit
The magnetic saturation voltage regulator circuit is designed to stabilize output voltage levels by utilizing magnetic saturation principles. This circuit typically employs a magnetic core, which operates in saturation to regulate voltage,...
5V power supply using 7805 IC with circuit diagram
A 5V power supply using IC 7805 is designed and explained with a neat circuit diagram.
The circuit for a 5V power supply utilizing the IC 7805 voltage regulator is a straightforward and efficient design that provides a stable output voltage...
CF1 CF2 DC power supply circuit
DC power supply with a shunt, rectifier, filter, limiter, and regulator. The circuit is simple and cost-effective, capable of meeting the requirements. The 6.3V indicator lights HL1 and HL2 indicate the lathe's running and stopping status through a relay control...