Top Circuits Page 32

Amplifier circuit of this paper is to introduce a floating power supply, the purpose is to increase the output power, the amplifier output power with only the final stage ampli..

Amplifier circuit shown in Figure 2-25. It has the following features: (1) promote the use of a class 6N11 tube for parallel push-pull amplification entire term, high-frequency..

As shown for the low-frequency output 7W power amplifier circuit. The circuit uses a FET input type operational amplifier LF356 integrated as a voltage amplification. The class..

As shown in FIG To eliminate hum instrument amplifier circuit. FIG amplifier stage A1, A2 selected integrated operational amplifier INA101, followed by level A3 selection INA10..

As shown in FIG constitute grounds PGA103 programmable gain instrumentation amplifier. This circuit uses the PGA205 and PGA103 cascading manner, the total gain of the amplifier..

As shown in FIG grounds PGA203 and isolation amplifier IS0102 constitute isolated programmable gain instrumentation amplifier circuit. PGA203 then amplified by the input signal..

As shown in FIG simple audio amplifier circuit. Using the integrated op-amp configuration of audio amplifier is stable, easy to negative feedback, so it is easy to get equaliza..

As shown in FIG source constituted by PGA203 programmable instrumentation amplifier suspended. Because the input signal is applied to PCA203 twisted pair inputs, so in suspensi..

As shown in Figure 3-30 to promote the use of IC LA4425 stage power amplifier, a pair of power module 1490 as a push-pull output, since the impedance converter, whether the spe..

As shown, the use of the operational amplifier A for audio preamplifier circuit. The advantage is small size, low noise, low power consumption, good consistency. A operational ..

As the main part of the circuit has been achieved Ic! Of bulk components are primarily large number of capacitors. Internal circuit shown, the output level from the A t, Tr. Co..

As we all know, from the amplifier output stage to the previous stage, although a large loop feedback to improve frequency response and harmonic distortion indicators amplifier..

Audio AGC can keep track, monitor audio preamplifier output signal level when the input signal increases, AGC circuit automatically reduces the gain of the amplifier; when the ..

Audio power amplifier circuit from LA4112 integrated power amplifier and other components of FIG. ..

Based CNC programming gain instrumentation amplifier PGA202/203 circuit diagram as follows: ..

Because all of the resistance values are equal, so the Cantonese OP amplifier 4 magnification number (A) is equal to l, but according to need, by selecting small exposed the ug..

By ISO120 and INA105 instrumentation amplifier as shown, multiplexer constituted 600V battery system battery monitoring circuit. This circuit 50 in series 12V battery (ie, the ..

By an integrated power amplifier TDA2040 (lC) can also form OCL power amplifier (OCL meaning is no output capacitor power amplifier). Circuit shown in Figure 10-10, which uses ..

By the pLPC1342V and NE (two company names and fever on the tube amplifier circuit 2SA1227A 2SC2987A composed of maximum output power up to 120W, the cutoff frequency up to 500..

Chinas national conditions, general living room area of more than twenty square meters, and usually doubles as a bedroom or living room listening room. If the speaker sensitivi..

Circuit shown in Figure 240 of the circuit structure is very simple, with only four transistors to achieve circuit from input voltage put large, inverted, and promote the whole..

Closed loop amplification circuit and by RL and. Decided, when magnification is 100 times (40dB), the input signal is high, in order to ensure a stable circuit work for, people..

Figure 4-20 is HAD250A-3 active speakers and amplifier circuit integrated amplifier circuit LM3886 thereof. The circuit uses 25V power supply, output power up to 50w 2, to meet..

This circuit is used to give out a microphone preamp to a amplifier which will power the signal. The NPN transistors used are ECG123A. This circuit is also a older model to the one that now use IC's, but dont worry this will still work fine...

Most audio amplifier systems must have preamplifiers with many different characteristics. These include high-gain linear response for magnetic microphones, low-gain linear response for tuners, and high-gain RIAA equalization for magnetic phone cartridges. To....

The Stereo Tape Head Preamplifier kit is based on LA3161 IC from SANYO. Power supply - 9 ~ 12 VDC @ 20 mA. Output power - upto 200 mW. Input Resistance - 100 K? (Typ), Load Resistance - 10 K? (Typ). Low noise, good ripple rejection owing to the on-chip....

The microphone has high sensitivity in the audio range, but in the ultrasonic range, the sensitivity decreases rapidly. The receiver is very sensitive. To prevent overdriving and feedback due to the high sensitivity of the microphone in the audio range, the....

In recent years, following CD`s introduction, vinyl recordings are almost disappeared. Nevertheless, a phono preamplifier is still useful for listening old vinyl discs from a well preserved collection. This simple but efficient circuit devised for cheap....

This preamplifier has a low output impedance, and is designed to drive long cables, allowing you to listen to a remote music source without having to buy expensive screened cables. The very low output impedance of around 16 ohms at 1KHz, makes it possible to....

Simple circuitry suitable for moving-magnet cartridges Passive high-frequency equalization. This simple but efficient circuit devised for cheap moving-magnet cartridges, can be used in connection with the audio power amplifiers shown in these webpages,....

The Sound Blaster 16 PCI and Sound Blaster 16 ISA do not have a very sensitive microphone input. This little one transistor amplifier is powered directly from the microphone jack on the sound card and has LOTS of gain. Just put a 100uF bypass capacitor in....

This circuit is suitable to amplify and distribute the audio signals. The input audio signal is applied to the J1 and after passing through the P1, It is buffered and amplified by the U1 prepared to redistribute. It has 3 output to drive 3 audio lines with....

Since the volume control is after the gain stage, the preamp can be easily overloaded. I tried to limit the input signal by mounting a 470 k resistor in series with the CD input. A voltage divider is formed by this resistor and R107, resulting in a greater....

This preamplifier was designed to cope with CD players, tuners, tape recorders etc., providing a gain of 4, in order to drive less sensitive power amplifiers. As modern Hi-Fi home equipment is frequently fitted with small loudspeaker cabinets, the bass....

This design was born of frustration with the mic preamp in my Sony R91. It clips at ridiculously low levels, basically it has 28mV of headroom to deal with an input that could be as high as 1800mV (depending on mic & volume), so this design attempts to cure....

Many amplifiers have phono inputs for connecting record players to the amplifier. Phono input is designed to take a up to few millivolt signal from phono pickup and amplify it. The amplifier stage does also some equalization based on standardized RIAA curve.....

The preamp featured is very straightforward to make on the PCB, and has an innovative tone defeat function. Rather than completely disable the tone controls, they are massively de-sensitised, and when "defeated" have a maximum range as shown in Fig. 3....

Most audio amplifier systems must have preamplifiers with many different characteristics. These include high-gain linear response for magnetic microphones, low-gain linear response for tuners, and high-gain RIAA equalization for magnetic phone cartridges. To....

The level at which the limiter kicks in audio can be adjusted with the selector knob LIMIT LEVEL. When this level is exceeded, the output of the half-LIMITING detector of the op-amp (used as a comparator) turns the LED causes the resistance of the....

This circuit has read the RIAA equalization, tone controls, and adequate gain to drive most power amplifiers conunercial by using CA3410 op amp BiMOS. Total harmonic distortion, pushed to provide an output of 6-V, is less than 0.035% in audio-frequency range....

Electronic switch is a multifunctional preamplifier. It consists of five-way touch electronic switch, high-speed DC servo RIAA ultralow distortion amplifier. It can be volume, ..

This circuit can be used for inductive pick-up elements and dynamic microphones Most soundcards have a line` input and one for an electret (condenser) microphone. To be able to connect an inductive tape-recorder head or a dynamic microphone, an add-on....

Low-noise preamplifier circuit It shows a typical low-noise preamplifier circuit, an amplifier may be used to signal ..

Adopt and put the intermodal servo preamplifier circuit as shown, the circuit is 115V, 60Hz servo motor amplifier provides a differential output. An op amp inverting connection..

Amp circuit as shown in the pre-television. The pre-amplifier circuit is Qioi and other parts of xlol. Q [ol and biasing element is configured as a common emitter IF amplifier,..

As shown for the OPA37 constitute a low-noise preamplifier. Input signal is applied OPA37-inverting input (pin 3), circuit RL, CL is the load impedance electromagnetic pickups,..

BA328 with Dual preamplifier circuit having fewer external components, easy installation features, single 8-pin DIP package. Circuit characteristics are as follows: wide operat..

Bong ordinary differential amplifier circuit and the difference circuit is that it has made a voltage-current conversion circuit rPl constituted with R. And Rl o of the OP ampl..

Circuit 90s common recorder head amplifier circuit, the choice of ultra low noise precision op amp OPA37 pre-formed head amplifier. Circuit can provide a standard NAB equalizat..

Circuit schematic as shown below, using the MC2830 voice circuit is formed. Traditional voice circuit can not distinguish between speech and noise of the input signal. In a noi..

Circuit shown in Figure 3-10. This is a multi-function input with a preamplifier, including the tuner input, a magnetic tape playback input, magnetic phono input and phono equa..

Circuit shown in Figure 3-8. Input signal through a low pass filter to the input of the differential amplifier FET former composition are evaluated once preamplifier output of ..

Figure 3-2 (b) is the second half of the circuit, VT17 ~ VT31 group into power amplifiers, pre-amplifiers, and it is a structure composed of exactly the same oIC2 its zero serv..

Figure 3-25 is a hybrid having four input preamplifier, in the circuit, cZ1, cz, C23 and cz4 respectively, can enter the microphone, line, phono and crystal head signal. Quad c..

This digital volume control has no pot to wear out and introduces almost no noise in the circuit. Instead, the volume is controlled by pressing UP and DOWN buttons. This simple circuit would be a great touch to any home audio project...

This simple circuit mixes two or more channels into one channel (eg. stereo into mono). The circuit can mix as many or as few channels as you like and consumes very little power. The mixer is shown with two inputs, but you can add as many as you want by just....

That circuit will provide an overall gain of one between the output and each input channel. Each input channel includes a single 0.1uf capacitor and 100-Kilohms resistor to provide an output impedance of 100K. The number of input channels to this audio mixer....

The target of this project was the design of a small portable mixer supplied by a 9V PP3 battery, keeping high quality performance. The mixer is formed assembling three main modules that can be varied in number and/or disposition to suit everyone needs...

This project is a 3 or more lines mixer. For more than 3 inputs you can repeat the input parts (P=10K R=22K). It powered with 9Vdc...

This simple circuit mixes two or more channels into one channel (eg. stereo into mono). The circuit can mix as many or as few channels as you like and consumes very little power. The mixer is shown with two inputs, but you can add as many as you want by just....

This circuit is useful for removing ground loop hum on a remote line level audio signal line. It can be used to to connect a computer sound card to a stereo amplifier`s line input. Other uses include tapping into a line level signal for powering a remote....

With this circuit you can mix four separate audio inputs. Each input will accept high or low impedance microphones, phonograph, tape or aux signals. You can adjust the gain of each input by adjusting each respective pot. With the Stereo/Mono switch you can....

Input Amplifier Module: a low noise circuit equipped with a variable voltage-gain (10 - 100) pre-set, primarily intended as high quality microphone input, also suitable for low-level line input. High-quality modular design. 9V Battery powered - Very low....

This is a classic signal mixer that is used for audio purpose. VR1 & VR2 are inputs audio volume controlers and VR3 is used to control the balance between Input1 and Input2. connect a dynamic microphone to Input1 and a music without vocal to Input2, then....

Most cards of sound in computer, are deprived stereo input for microphone, on the contrary have stereo input for high level [ Line ]. The circuit uses the input Line of card of sound, in order to we place a two mono stereo microphone, in the input of card of....

I designed this circuit for one friend of mine to be used as a small portable DJ mixer. The circuit is an audio mixer circuit so simple as it can be. There are two dual logarithmic potentiometers in the circuit to adjust the input signal levels and some....

The mixer is the common "virtual earth" mixing amplifier, and there is nothing special about it. Note that it is inverting, which complements the tone controls (also inverting) so the absolute signal polarity is maintained. As shown, the mixer also has a....

A TL081 op amp is used as a high impedance to low. converter and a signal mixer. The input impedance is about 1 megohm and the output impedance is about 1 kohm. Two 9 volt batteries are used as power source. ..

This circuit can be used as a mixer and a stereo track four. The quad op-RNAP IC gives a little gain for each track, the pan control provides panning between one and two tracks with the switch to high, and with the switch to low, it is possible to pan....

Balanced diode mixer circuit is shown. Diode 2AP9 2. Due to the use of two diodes and the voltage is large, the diode operates in the off state, it is also known diode switch tube balanced mixer...

Balanced mixer circuit is shown by the two dual-gate field effect transistor. RF signal by the input signal transformer Tl effect transistors coupled to the gate of the two, th..

Chemical mixer circuit having a stirring speed, thermostat and timer alarm function can be used in chemical, steel and other industries. (1) circuit works heating magnetic stir..

Commonly used in industrial and mining enterprises power mixer, mixing materials because often smell or dust, the operator should not be too close to the contact. Light control..

This complete high quality, low noise 5-BAND GRAPHIC EQUALIZER circuit is based around Monolithic Linear integrated circuit LA3600 manufactured by SANYO. This circuit is very easy to build and has good Quality. You can use it with Portable component stereos,....

The circuit shown in Figure 1 uses only two ICs, and has a bandwidth that is adjustable from more than one octave down to a tenth of an octave. As shown, the frequency range is 20 Hz. to 20 KHz. in three bands, although a fourth subsonic band could be added....

In essence, it uses the same principle as a graphic equaliser, but the simulated inductors are made variable, so the frequency can be swept back and forth. The four 10K pots provide cut (when on the left or anti-clockwise side of centre) or boost, and in the....

The Linkwitz transform circuit (or EAS principle) will allow any driver to extend to 20 Hz or even lower. A good quick test is to stick the speaker in a box, and drive it to 50 or 100W or so at 20 Hz - you should see a lot of cone movement, a few things will....

I came up with this idea when I was in a situation where ... * I had an amplifier with an unused RIAA input and * I was missing another input for a standard audio signal at this amplifier. So I designed a miniature passive network to convert a....

Vinyl equalisation (EQ) has been with us in a stable and predictable form for quite a long time, but for those who are interested in the old 78 rpm records there are a great many problems to overcome. One of these is obtaining a turntable that runs at 78....

This circuit allows you to equlize the audio signals in ten band. It uses low cost op-amps to form a professional equalizer circuit. The heart of the design is a classical band-pass active filter. The U11 acts as an attenuator to prepare the signal level for....

2 versions of the equalization circuit, the first having 6 db less insertion loss than the other. However, some may not be able to find a .68 microfarad capacitor. The second version uses a more common .22 microfarad capacitor. Both of these circuits operate....

The project described in this article is a constant Q, fully expandable graphic equaliser. Where most "conventional" graphic EQ circuits have a Q that is dependent on the setting of the pot, this one maintains the same Q at all settings. This is achieved by....

A simple 3-way crossover, intended for triamping Hi-Fi systems. This is a conventional 12dB / Octave unit, and cannot be expected to have the same performance as a Linkwitz-Riley aligned filter network. It will still be a vast improvement over nearly any....

This complete high quality, low noise 5-BAND GRAPHIC EQUALIZER circuit is based around Monolithic Linear integrated circuit LA3600 manufactured by SANYO. This circuit is very easy to build and has good Quality. You can use it with Portable component stereos,....

M5227P is the application circuit, for graphic equalizer, its control curve is always logarithmic frequency axis to represent rate, and require the same control curve pitch equal to ensure that the band..

Another example of application is extended. It uses TA7796 and five external transistor to form a ten -band equalizer circuit, the lowest center frequency of the equalizer for ..

Figure 1-97 is a ten-band equalizer circuit with a first connection thereof. FIG lC is the utility voltage amplifier, R7, respectively, equivalent to the island in Fig 1-92 Rl,..

Figure 1-98 is a double five-band equalizer circuit composed of a second connection. FIG IC1 IC14 respectively equalizer per channel utility voltage amplifier; ICLl, IC24, IC 2..

Figure 1-99 with a five-band equalizer equalizer circuit TA7796 specific integrated circuit composed of the circuit in the public electricity voltage amplifier, an analog induc..

Figure 3-16 is a low-noise preamplifier equalizing HA12017 consisting playback circuit, the circuit R3, R4 and C4, in line with standard maggots balanced network. The gain stag..

Figure 4-33 and using substantially the same circuit configuration, the common amplifier and analog inductive circuits are provided, but its analog inductive circuit transistor..

The LTC1050 is confi gured as unity gain 2nd order low-pass fi lter which center frequency is (1.2πR´C´) = 1.72 • fCUT-OFF = 17.2Hz and Q = 0.5. Figure 2 shows the amplitude response of the fi lter, and Figure 3 shows a well behaved transient response for....

Although you can obtain universal, resistor-programmable switched -capacitor filters that are configurable as notch filters, most cannot operate at bandwidths higher than 100 kHz. Further, the typically 16- to 20-pin packages do not include a continuous....

It is very useful (and has Best Quality) for 1 -100watt AUDIO AMPLIFIERS..

By selecting an attenuation switch to change the pitch of a feedback control circuit transition frequency real cases. Hu) for 2 treble controls,..

The application that to you we propose is a simple filter of region that limits the acoustic region (20-20000Hz) in the region 20-100Hz. With the manufacture that to you we propose you can make a active filter in order to you lead a loudspeaker of very....

This circuit is used to convert a mono audio signal into a stereo signal that can be panned between the left and right channel by a 0-10V control signal, it is intended for analog synthesizer systems...

This device is a microprocessor controlled waveform generator that can be used for driving a voltage controlled stereo panner for music applications. Panning is simply the movement of a mono audio signal between the left and right channels of a stereo sound....

The controller is quite (actually very) simple. An input buffer ensures that the input impedance of the source does not affect the integrator performance, and allows summing of left and right channels without any crosstalk. The output provides a phase....

These filters are useful for equalisation, analysis and other tasks such as the Sound to Light converter (Project 62) or even a fully functional Vocoder. For those who have not heard of the vocoder, it is a device that takes a music source as one input and....