Simple A/D converter circuit with 2504
Time IO-bit conversion is 3.3 MHz with a p 3. Clock. This converter uses an approximation 2504 12-bit register in successive operating mode where the short-cycl...
High Speed A/D converter 12-bit
This system performs a complete conversion of 12 bits in 10 p unipolar or bipolar. This converter is accurate to ± 12-bit LSB Y2 and a typical gain TC of 10 ...
A/D Converter with LT1018
The converter has a 60-ms conversion consumes 460 pA of 1's. 5 V power supply and maintains an accuracy of 10 bits on a 15 ° C in the temperature range of 35...
10 Bit A-D converter circuit
Each time a pulse is applied to the conversion of the control input, Ql resets the 1000 pF capacitor to 0 V. This action takes 200 ns to reset the falling edge ...
16 bit Analogue to Digital Converter LTC1052
The circuit here is a A/D converter, that consisting of A2, a flip-flop, some doors and a current sink, is based on a current balancing technique. Again, the st...
Analogue to digital converter circuit
That simple 4 digits converter circuit has OUTPUT COUNT = 1 according to my f-IMHz to 10.000. All diodes are IN4146 "POLYSTYRENE" NPO. ...
14 Bit A-D Converter with ICL7134B
The circuit ICL7134B base is a bipolar input AID converter broadband, using two AM25L03s to form a successive approximation register 14-bit. The comparator is a...
Video speed 6-bit Flash A/D converter
This circuit use the CA3306 a family of CMOS parallel (flash) analogue to digital converters designed for low power, high speed applications. The CA3306CE opera...
Analog Tachometer Readout
The analog display consists of a frequency/voltage converter (IC12) and bar-graph segment drivers IC10 and IC11. ...
Calibrated-tachometer
Here is a simple tachometer circuit for use with a hand-held DVM or portable chart recorder. A novel feature is that the source frequency pulse/rev rate can be...
Analog Volt and ampere meter
For those who labvoeding built and flow of tension and a leader in providing circuit below was developed. If meter is a moving-coil meter 100?A useful. You have...
Analogue Ohm meter
This is a simple ohm meter that is small to build. The circuit operates with a constant current around T1. The current depends on the emitter through S1 can be ...
Zener Tester schematic
With this simple measuring device can: Determine the Zener voltage up to 25V. The connections of cathode and anode of each diode finding. Check if a diode fails...
Conductivity Tester circuit
This little guide for every electronics tester would actually have to lie in the toolbox. You can have components such as resistors, capacitors, diodes, etc. of...
LED Digital Thermometer schematic
This digital thermometer indicates the temperature measured with an NTC using 7 LEDs. The circuit works using an opamp, the well-known 741, which amplifies the ...
99 mV to 999 mV meter schematic
This circuit can for example be incorporated into a diet to pressure warning. The meter can measure voltages from -99 mV to 999 mV. The circuit uses two ICs, th...
60-70dB Decibel Meter schematic
The circuit below responds to sound pressure levels from about 60 to 70 dB. The sound is picked up by an 8 ohm speaker, amplified by a transistor stage and one ...
Milliamp Meter to Voltmeter
A milliamp meter can be used as a volt meter by adding a series resistance. The resistance needed is the full scale voltage reading divided by the full scale cu...
Battery capacity / Accumulator Charge Meter
The instrument used to measure battery capacity. The battery may be charged to any current in the range 0-3 A. The load current may be constant, may change over...
Field, Crystals and capacitance meters schematics
Because it uses few parts, a printed circuit board is not necessary; components can simply be soldered to one another. However, a box is desirable for operating...